sphynxhate9

The Key Lab could be time to change the battery if the 500 remote key fob isn't working. If you replace the battery, but it still doesn't work the issue could be elsewhere. United Locksmith specializes in the production of new keys for classic cars. We have the tools and parts needed for this job. Dead Coin Battery The most frequent reason that your Fiat 500 key fob will not unlock or lock the doors is a dead battery. The key fob is equipped with an internal battery called a coin cell that is prone to draining quickly when it isn't frequented enough. If your remote has started to show signs like a loss in range or stopped functioning or not responding, then the battery could be dead. The battery inside the key fob is secured by metal retaining clips. If the clips aren't secure, they could cause problems with contact that can prevent your remote to receive power. Make use of a flathead screwdriver to pry open the retaining clip and remove the battery. Make sure to use a battery with the same voltage, size, and specification as the original. The key fob can also become corroded or damaged by water exposure. Even a quick bath in soapy, warm water can damage the chip. It is best to keep your key fob in a dry place. Water Damage If your key fob isn't functioning properly, it could be caused by water damage. Key fobs are fitted with rubber seals to protect them from being damaged by rain or a splash of water, but it is crucial to keep your car keys out of the pool, ocean and washing machine! The key fob comes with an electronic chip inside it that transmits a signal to your car's immobilizer system. The chip allows the 500 to lock and start. If it gets wet, however it will cease to function. If you're looking to determine if your key fob is still functioning You can clean the internal electronics using isopropyl or an electronic cleaner. It is recommended to replace the key fob when it's submerged into salt water rather than attempting to fix it yourself. A replacement fob may cost you a little bit however it's much less expensive than paying to have your Fiat 500 towed to a dealer and repaired there! You can also fix it yourself by following just a few steps. Be sure to have the correct type of battery before attempting to open your keyfob. This is a job that's much easier than it looks and you can find step-bystep instructions on the internet for nearly any key fob for cars. Faulty Chip The chip inside the key fob communicates to your car's immobiliser unit to ensure the car is able to start when the correct key is used. If the chip is damaged or corrupted in any way it will not start. A chip that is defective can happen due to many reasons, but the most common cause is water damage or a dead battery. It is recommended to leave the job to a professional locksmith who will be able to replace the chip quickly and at a reasonable price. If your key fob will not work after being exposed to clean rain or tap water take the battery off. Wipe down the electronic component using a towel. If the key fob doesn't work it's probably an issue with the chip and will require replacement. A few people will visit their dealer when they require a new Fiat fob. However, this could be a costly option. If you're seeking a cost-effective method to get your Fiat key fob fixed, look no further than United Locksmith. We have the tools and experience needed to repair your Fiat fob in a professional and timely manner. Faulty Receiver Module Fiat key fobs transmit an electronic signal to the vehicle that will unlock and lock doors (and start the car for vehicles with an automatic transmission) up to 50 feet. There are a few reasons why the fob might stop working. This could be due to a dead battery water damage, worn out buttons as well as a receiver issue. signal interference, or a malfunctioning chip. If the fob is in a pocket which has suffered extreme trauma (such as being dropped onto the floor or washed in the washer), it may not be able to communicate with the Body Control Module (BCM) of the car. The BCM is a security device which will only accept signals from genuine keys. You'll have to replace the fob if this occurs. A professional locksmith can handle the entire process of replacing your key including programming a new key for your 500. They can even provide you with an clone fob that performs the same as the original (and costs only less than what it would cost).